Exactly How to Install a Tub Yourself: Removing and Replacing.
Exactly How to Install a Tub Yourself: Removing and Replacing.
Blog Article
We've unearthed this great article on How to Install a Bathtub Yourself below on the internet and thought it made good sense to write about it with you here.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult task. If the old bathtub is readily easily accessible, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. Make certain you have certified yourself for the task and fit attempting it. Instead of working with a specialist to take over a halfway-completed job, it is better to think about using one before you start. Chances are you might require an expert plumber to make tube links.
This short article will certainly help you mount a new bath tub in your shower room if you have currently bought a brand-new tub and also don't require to alter the setup of your previous water system pipes.
Your devices and product list must comprise the following:
Planning for the Installation
To start with, the sustaining frame provided with the bath ought to be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the bathtub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The process of eliminating the existing faucets can be rather troublesome as a result of the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Before proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are valuable in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable tap port to the ideal supply pipeline by making a compression join; after that do the very same for the various other tap.
Activate the water system and examine all joints and new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow outlet as well as the normal outlet for leakages.
Lastly, take care of the bath paneling as described in the maker's user's manual. Tiling and securing around the bathtub must wait till the tub has actually been used a minimum of when as this will settle it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in location in between the tap and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous type ought to be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, causing problems with moisture and feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to allow for the motion experienced when the bathtub is in use. The sealant can break relatively very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is advisable to fit the floor tiles making use of waterproof or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on A Step-by-Step Guide to Installing a Bathtub, I thought sharing that piece of content was really helpful. Make sure you take the time to promote this entry if you enjoyed it. I cherish reading our article about How to Install a Bathtub Yourself.
Browse Our Site Report this page